SAE J1127簡介

SAE J1127是關(guān)于車輛電氣系統(tǒng)低壓60伏直流電壓(25伏交流電)或更小的電池電纜表面的測試標準。該試驗的目的是確保電線電纜符合要求。以下為部分英文標準原文，出于版權(quán)保護，如需SAE J1127標準全文或SAE J1127中文版本標準，請垂詢客服人員。

1. Scope

This SAE Standard covers low tension battery cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.

2. References

2.1 Applicable Publications—The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply.

2.1.1 SAE PUBLICATIONS—Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.

SAE EA-1128—Wire Color Charts

SAE J311—Fluid for Passenger Car Type Automatic Transmission Dictionary of Materials and Testing

2.1.2 ASTM PUBLICATIONS—Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.

ASTM B 33—Standard Specification for Tinned Soft or Annealed Copper Wire

ASTM B 174—Standard Specification for Bunch-Stranded Copper Conductors for Electrical Conductors

ASTM B 263—Method for Determination of Cross-Sectional Area of Standard Conductors

ASTM B 298—Standard Specification for Silver-Coated Soft or Annealed Copper Wire

ASTM B 354—Definitions of Terms Relating to Uninsulated Metallic Electrical Conductors

ASTM B 355—Standard Specification for Nickel-Coated Soft or Annealed Copper Wire

ASTM D 412—Standard Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermoplastic Elastomers—Tension

ASTM D 471—Standard Test Method for Rubber Property—Effect of Liquids

ASTM D 573—Standard Test Method for Rubber —Deterioration in an Air Oven

ASTM E 145—Standard Specification for Gravity—Convection and Forced-Ventilation Ovens

ASTM F 1251—Standard Terminology Relating to Polymeric Biomaterials in Medical and Surgical Device

2.1.3 IEC PUBLICATION—Available from ANSI, 11 West 42nd Street, New York, NY 10036-8002.

IEC—Electricity, Electronics and Telecommunications, Multilingual Dictionary

2.2 Related Publications—The following publications are provided for information purposes only and are not a required part of this specification.

2.2.1 SAE PUBLICATIONS—Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.

SAE J156—Fusible Links

SAE J1067—Seven Conductor Jacketed Cable for Truck Trailer Connections

SAE J1128—Low Tension Primary Cable

SAE J1292—Automobile, Truck, Truck-Tractor, Trailer, And Motor Coach Wiring

SAE J1654—High Voltage Primary Cable

SAE J1673—High Voltage Automotive Wiring

SAE J1678—Low Voltage, Ultra Thin Wall Primary Cable

2.2.2 ASTM DOCUMENTS—Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.

ASTM B 1—Standard Specification for Hard-Drawn Copper Wire

ASTM B 3—Standard Specification for Soft or Annealed Copper Wire

ASTM B 8—Concentric-Lay-Stranded Copper conductors, Hard, Medium-Hard, or Soft

ASTM B 787—19 Wire Combination Unilay-Stranded Copper Conductors for Subsequent Insulation

2.2.3 IEC PUBLICATION—Available from ANSI, 11 West 42nd Street, New York, NY 10036-8002. IEC 811-2-1—Common test methods for insulating and sheathing materials of electrical cables—Part 2: Methods specific to elastomeric compounds—Section 1: Ozone resistance test—Hot set test—Mineral oil immersion test.

2.2.4 ISO DOCUMENTS—Available from ANSI, 11 West 42nd Street, New York, NY 10036-8002. ISO 6722—Road vehicles—Unscreened 60 V and 600 V single core cables—Test methods, dimensions and requirements

ISO 14572—Road vehicles—Round, unscreened, 60 V and 600 V multicore sheathed cables—Basic and high performance test methods and requirements